Lenovo TD100 User Manual

ThinkServer TD100 and TD100x Types 639 8, 6399,6419, 6429, 4203, 4204, 4205, and 4206Hard ware Maintenan ce Man ual

Guidelines for trained service techniciansThis section contains information for trained service technicians.Inspecting for unsafe conditionsUse the in

Installing an adapterFor information about the types of adapters that the server supports and otherinformation that you might consider when installing

1 Rear adapter-retention bracket2 Adapter3 Front adapter-retention bracket7. Rotate the rear and front adapter-retention brackets to the closed

Removing and installing internal drivesSee the User Guide for information about the types of drives that the serversupports. The following figures sho

1 Bay 1 5 Bay 52 Bay 2 6 Bay 63 Bay 3 7 Bay 74 Bay 4Chapter 4. Removing and replacing server components 85

Removing a CD or DVD driveTo remove a CD or DVD drive, complete the following steps.1. Read the safety information that begins on page vii and “Instal

Installing a CD or DVD driveTo install a CD or DVD drive, complete the following steps:1. If you are replacing a removed drive with a new drive, make

a. Remove the hot-swap power-supply. Press down on the orange releaselever and pull the power supply out of the bay, using the handle.b. Lift up the p

10. If you have a hot-swap model, reinstall the hot-swap power supplies (see“Installing a hot-swap power supply” on page 96).11. Install the side cove

Installing a hot-swap hard disk driveBefore installing a hot-swap hard disk drive, read the following information:v The hot-swap drives must be either

9. Check the hard disk drive status indicator to make sure that the hard disk driveis operating correctly. (You might have to restart the server for t

Guidelines for servicing electrical equipmentObserve the following guidelines when servicing electrical equipment:v Check the area for electrical haza

Removing a simple-swap hard disk driveAttention: Simple-swap hard disk drives are not hot-swappable. Disconnect allpower from the server before removi

Installing a simple-swap hard disk driveAttention: Simple-swap hard disk drives are not hot-swappable. Disconnect allpower from the server before remo

Removing a hot-swap power supplyThis procedure applies only to server models that have hot-swap power supplies.See “Removing a non-hot-swap power supp

Statement 17:CAUTION:The following label indicates moving parts nearby.To remove a hot-swap power supply, complete the following steps:1. Read the saf

Installing a hot-swap power supplyThis procedure applies only to server models that have hot-swap power supplies.See “Installing a non-hot-swap power

Removing a memory moduleTo remove a dual inline memory module (DIMM), complete the following steps.1. Read the safety information that begins on page

Installing a memory moduleThe following notes describe the types of dual inline memory modules (DIMMs) thatthe server supports and other information t

v The server supports memory mirroring (mirroring mode) and online-sparememory.– Memory mirroring replicates and stores data on DIMMs within two branc

changes. For more information on the Configuration/Setup Utility program, seethe User Guide. When you use online-spare memory, you must consider thefo

Attention: Static electricity that is released to internal server components whenthe server is powered-on might cause the server to stop, which could

Safety statementsImportant:Each caution and danger statement in this documentation begins with a number.This number is used to cross reference an Engl

9. Insert the DIMM into the connector by aligning the edges of the DIMM with theslots at the ends of the DIMM connector1 and 2. Firmly press the D

11. If you have a hot-swap model, reinstall the hot-swap power-supplies.If you have other options to install or remove, do so now; otherwise, go to “I

Removing a hot-swap fanAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate the server for more tha

Installing a hot-swap fanAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate the server for more t

Removing the rear system fan cage assembly with baffleAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not

3. Connect the rear fan 1 cage assembly cable to the system board (see“System-board internal connectors” on page 10 for the location of the rear fan

Removing the front system fan cage assemblyAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate the

Installing the front system fan cage assemblyAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate t

Removing the front USB connector assemblyTo remove the front USB connector assembly, complete the following steps.1. Read the safety information that

Installing the front USB connector assemblyTo install the front USB connector assembly, complete the following steps.1. Carefully feed the front USB c

Statement 1:DANGERElectrical current from power, telephone, and communication cables ishazardous.To avoid a shock hazard:v Do not connect or disconnec

6. If necessary, remove the Remote Supervisor Adapter II SlimLine retention taband store it for future use.Installing the rear adapter retention brack

Removing the front adapter-retention bracketTo remove the front adapter-retention bracket, complete the following steps:1. Read the safety information

Removing and replacing Tier 2 CRUsYou may install a Tier 2 CRU yourself or request Lenovo to install it, at no additionalcharge, under the type of war

Statement 2:CAUTION:When replacing the lithium battery, use only Lenovo Part Number 33F8354 oran equivalent type battery recommended by the manufactur

3. Carefully open the retaining clip on each end of the ServeRAID 8k-l adapterconnector and remove the adapter from the server.4. If you are instructe

the system board. The ServeRAID-8k adapter 1 is not cabled to the systemboard, and no rerouting of the SAS or SATA cable is required.To remove the S

5. Press the ServeRAID-8k adapter firmly into the connector.6. Mount the battery pack to the chassis, using the two mounting screws.1 Battery cable

Note: Remove the dust shield 1 (if one is present) from the Hot-swapSAS/SATA 1 signal connector 2on the system board before installing thesignal c

The following illustration shows how the cables must be connected whenyou install the ServeRAID-8k Controller into the simple-swap SATA model.1 SAS/

1 Plastic push pin 3 DIMM air duct2 Positioning pins 3 Screws6. Push the air duct up toward the rear of the power supply cage. Once the locato

Statement 2:CAUTION:When replacing the lithium battery, use only the battery recommended by themanufacturer. If your system has a module containing a

Removing the control-panel assemblyTo remove the control-panel assembly, complete the following steps.1. Read the safety information that begins on pa

10. Press up on the release latch 1 of the control-panel assembly 2 and pullthe assembly toward the rear of the server. After you pull the assembl

Installing the control-panel assemblyTo install the control-panel assembly, complete the following steps.1. Position the front end of the control-pane

Removing and replacing FRUsField replaceable units (FRUs) must be installed only by trained service technicians.Removing the hot-swap power-supply cag

6. While supporting the power-supply cage2, remove the three screws 1 fromthe pivot bracket that secure the power-supply cage to the chassis; then

Installing the hot-swap power-supply cage assemblyTo install the hot-swap power-supply cage assembly, complete the following steps.1. Align the screw

3. Return the power-supply cage handle to the locked position.4. Reinstall the hot-swap power supplies (see “Installing a hot-swap power supply”on pag

v Non-hot-swap models, lift up the power-supply cage handle and pull thepower-supply cage assembly all the way up until the retainer latch locks theca

Installing the simple-swap backplate (TD100 - some models)This procedure applies only to server models that have a simple-swap backplateinstalled on t

Removing the SAS/SATA backplaneTo remove the SAS/SATA backplane, complete the following steps.1. Read the safety information that begins on page vii a

Statement 4:≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb)CAUTION:Use safe practices when lifting.Statement 5:CAUTION:The power control button

Installing the SAS/SATA backplaneTo install the SAS/SATA backplane, complete the following steps.1. Insert the bottom tabs of the SAS/SATA backplane w

Statement 11:CAUTION:The following label indicates sharp edges, corners, or joints nearby.Statement 17:CAUTION:The following label indicates moving pa

6. While you support the power-supply, remove the three screws from the pivotbracket that secure the power supply to the chassis; then, lift the power

Installing a non-hot-swap power supply cage assembly (TD100 - somemodels)To install a non-hot-swap power supply, complete the following steps.1. Align

5. Lift up the power-supply cage handle and pull the power-supply cage assemblyall the way up until the retainer latch locks the cage in place on the

Removing the microprocessor and heat sinkTo remove the microprocessor and heat sink, complete the following steps.1. Read the safety information that

Important: Be careful when you handle the microprocessor and heat sink. If the microprocessor and heat sink will be reused, do not contaminatethe ther

Installing a microprocessor and heat sinkImportant: Some models support dual-core processors and quad-core processors.Do not mix dual-core and quad-co

4. Carefully place the microprocessor into the microprocessor socket.Note: To maintain the correct orientation between the microprocessor and themicro

b. Turn the VRM so that the keys align with the slot.c. Insert the VRM into the connector by aligning the edges of the VRM withthe slots at the end of

Statement 8:CAUTION:Never remove the cover on a power supply or any part that has the followinglabel attached.Hazardous voltage, current, and energy l

Note: 0.01mL is one tick mark on the syringe. If the grease is properly applied,approximately half (0.22 mL) of the grease will remain in the syringe.

Removing the system boardTo remove the system board, complete the following steps.1. Read the safety information that begins on page vii and “Installa

11. Slide the system board toward the front of the server to disengage the tabsfrom the chassis; then, grasp the handles and Iron each side and carefu

Installing the system boardTo install the system board, complete the following steps.1. Grasp the system board by the handles and insert the system bo

Easy LED Diagnostics panel (TD100x only)To remove the Easy LED Diagnostics panel, complete the following steps.Light pathdiagnostics panelRelease Tab1

Chapter 5. DiagnosticsThis chapter describes the diagnostic tools that are available to help you solveproblems that might occur in the server.If you c

POST beep codesA beep code is a combination of short or long beeps or series of short beeps thatare separated by pauses. For example, a “1-2-3” beep c

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Statement 11:CAUTION:The following label indicates sharp edges, corners, or joints nearby.Statement 17:CAUTION:The following label indicates moving pa

No-beep symptomsThe following table describes situations in which no beep code sounds when POSTis completed.v Follow the suggested actions in the orde

Error logsThe POST error log contains the three most recent error codes and messages thatwere generated during POST. The BMC log and the system-event

contents of the BMC log also from the diagnostic programs. For completeinformation about using the Configuration/Setup Utility program, see the UserGu

POST error codesThe following table describes the POST error codes and suggested actions tocorrect the detected problems.v Follow the suggested action

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

xvi ThinkServer TD100 and TD100x: Hardware Maintenance Manual

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Checkout procedureThe checkout procedure is the sequence of tasks that you should follow todiagnose a problem in the server.About the checkout procedu

Performing the checkout procedureTo perform the checkout procedure, complete the following steps:1. Is the server part of a cluster?v No: Go to step 2

Chapter 1. IntroductionThis Hardware Maintenance Manual contains information to help you solveproblems that might occur in the Lenovo ThinkServer TD10

Troubleshooting tablesUse the troubleshooting tables to find solutions to problems that have identifiablesymptoms.If you cannot find the problem in th

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

General problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3,

Intermittent problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapte

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Memory problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “

Microprocessor problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chap

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Optional-device problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Cha

These updates are available from the Lenovo Web site. Complete the followingsteps to check for updated documentation and technical updates.Note: Chang

Power problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “P

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

ServerGuide problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter

Universal Serial Bus (USB) port problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis

Error LEDsThe following is an illustration of the system board LEDs.The system board haserror LEDs that will help to locate the source of the error. R

2. Check the front and rear of the server to determine whether any componentLEDs are lit.3. Remove the server cover and look inside the server for lit

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Diagnostic programs, messages, and error codesThe diagnostic programs are the primary method of testing the major componentsof the server. As you run

The keyboard and mouse (pointing device) tests assume that a keyboard andmouse are attached to the server. If no mouse or a USB mouse is attached to t

Diagnostic error codesThe following table describes the error codes that the diagnostic programs mightgenerate and suggested actions to correct the de

ThinkServer TD100 features and specifications (Machine Types 6398,6399, 6419, 6429, 4203, 4204, 4205, and 4206)The following information is a summary

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Server controls, LEDs, and connectorsThis section describes the controls, light-emitting diodes (LEDs), and connectors onthe front and rear of the ser

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Recovering from a BIOS update failureIf power to the server is interrupted while BIOS code is being updated, the servermight not restart correctly or

14. Replace any adapters that you removed (see “Installing an adapter” on page82); then, install the side cover (see “Installing the side cover” on pa

System-error log messagesA system-error log is generated only if a Remote Supervisor Adapter II SlimLine isinstalled. The system-error log can contain

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

The following illustration shows the controls, LEDs, and connectors on the front ofthe simple-swap server models.1 System power LED 5 USB connecto

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See Chapter 3, “Parts listing,

Solving SCSI problemsNote: This information also applies to Serial Attached SCSI (SAS) problems.For any SCSI error message, one or more of the followi

Solving Ethernet controller problemsThe method that you use to test the Ethernet controller depends on which operatingsystem you are using. See the op

Solving undetermined problemsIf the diagnostic tests did not diagnose the failure or if the server is inoperative, usethe information in this section.

Calling Lenovo for serviceSee “Getting help and technical assistance” on page 217 for information aboutcalling Lenovo for service.When you call for se

Getting help and technical assistanceIf you need help, service, or technical assistance or just want more informationabout Lenovo products, you will f

Calling for serviceDuring the warranty period, you can get help and information by telephone throughthe Customer Support Center.These services are ava

Service methods and procedures vary by country, and some services might not beavailable in all countries. International Warranty Service is delivered

220 ThinkServer TD100 and TD100x: Hardware Maintenance Manual

Appendix. NoticesLenovo may not offer the products, services, or features discussed in this documentin all countries. Consult your local Lenovo repres

An LED on the system board might also be lit to help isolate the error. SeeChapter 5, “Diagnostics,” on page 147 for additional information.USB connec

estimated through extrapolation. Actual results may vary. Users of this documentshould verify the applicable data for their specific environment.Trade

Maximum internal hard disk drive capacities assume the replacement of anystandard hard disk drives and population of all hard disk drive bays with the

Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenneet à la Norvège.L’etiquette du système respecte la Directive européenne 20

Les batteries ou emballages pour batteries sont étiquetés conformément auxdirectives européennes 2006/66/EC, norme relative aux batteries et accumulat

Industry Canada Class A emission compliance statementThis Class A digital apparatus complies with Canadian ICES-003.Avis de conformité à la réglementa

Deutschland:Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit vonBetriebsmitteinDieses Produkt entspricht dem “Gesetz über die elekt

Taiwanese Class A warning statementChinese Class A warning statementKorean Class A warning statement228 ThinkServer TD100 and TD100x: Hardware Mainten

IndexAac good LED 188acoustical noise emissions 3Adaptec RAID Configuration Utility 19adapterhot-plug devices 116installing 82hot-plug 116removing 81S

display problems 178drive bays, internal 84drivesbay 1, 2, or 3installing 87removing 86bay 4, 5, 6, or 7hot-swap, installing 90hot-swap, removing 89si

hot-plug adapter.See adapterhot-swap and hot-plug devicesadapters 116hot-swap drivespecifications 3hot-swap drivesSAS backplane LEDs 6hot-swap drives,

Rear viewThe following illustration shows the LEDs and connectors on the rear of thehot-swap power supply models with optional redundant power.1 Pow

Oonline publications 2optionconnectors 12optional deviceproblems 181optionsmemory modules 98order of installationmemory modules 100, 101Pparallel conn

SSAS backplaneinstalling 132LEDshot-swap drive activity 6hot-swap drive status 6SAS or SATA hot-swap drivesinstalling 90removing 89SAS/SATA backplaner

video problems 178viewing the configurationSAS/SATA controller 18Serial ATA controller 20VRMinstalling 141Wweb sitepublication ordering 217support 217

Part Number: 46U0860Printed in USA(1P) P/N: 46U0860

1 Power cord connectors (somemodels)7 USB 3 and 4 connectors2 Mouse connector 8 (RJ45) Ethernet 10/100/1000connector3 Keyboard connector 9

Video connectorConnect a monitor to this connector.USB connectorsConnect USB devices to these connectors.Ethernet connectorUse this connector to conne

Internal connectors, LEDs, and switchesThe following illustrations show the connectors, light-emitting diodes (LEDs), andswitches on the system board.

System-board external connectorsThe following illustration shows the external input/output (I/O) connectors on thesystem board.123456789101112DIMM LED

ThinkServer TD100 and TD100x Types 639 8, 6399,6419, 6429, 4203, 4204, 4205, and 4206Hard ware Maintenan ce Man ual

System-board option connectorsThe following illustration shows the system-board connectors for user-installableoptions.123456789101112DIMM LEDs1 DIM

System-board LEDsThe following illustration shows the LEDs on the system board.123456789101112DIMM LEDs1 Microprocessor error LED (2) 5 ServeRAID

System-board switchesThe following illustration shows the switches on the system board.123456789101112DIMM LEDs1 SW32 SW4 (Boot block/Clear CMOS)T

Chapter 2. Configuration information and instructionsThis chapter provides information about updating the firmware and using theconfiguration utilitie

Using the Configuration/Setup Utility programThe Configuration/Setup Utility program is part of the BIOS code. You can use it to:v Change interrupt re

v The integrated SATA controller (simple-swap SATA models) with integrated SATARAID (also known as HostRAID) supports RAID level-0 and level-1 when tw

Select this choice to create, manage, or delete arrays, add or delete a hot-sparedrive, or initialize drives.v SerialSelect UtilitySelect this choice

Enabling the Serial ATA (SATA) controller: To enable the SATA RAID controller,complete the following steps:1. Turn on the server.2. When the prompt Pr

4. From the list of ready drives, select the two drives that you want to group intothe array.5. When you are prompted to select the RAID level, select

Configuring the controllerBy running ServeRAID Manager in Startable CD mode, you can configure thecontroller before you install the operating system.

Note: Before using this information and the product it supports, read the general information in “Notices,” on page 221, and theWarranty and Support I

10. Exit from ServeRAID Manager, and remove the CD from the CD or DVD drive.11. Restart the server.Viewing the configurationYou can use ServeRAID Mana

Using the Boot Menu programThe Boot Menu program is a built-in, menu-driven configuration program that youcan use to temporarily redefine the first st

24 ThinkServer TD100 and TD100x: Hardware Maintenance Manual

Chapter 3. Parts listing, TD100 Types 6398, 6399, 6419, 6429,4203, and 4206The following replaceable components are available for the ThinkServer TD10

Replaceable server componentsReplaceable components are of three types:v Self-service customer replaceable unit (CRU): Replacement of self-serviceCRUs

Table 3. Parts listing, Types 6398 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 3. Parts listing, Types 6398 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 3. Parts listing, Types 6398 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 3. Parts listing, Types 6398 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 3. Parts listing, Types 6398 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

ContentsSafety ...viiGuidelines for trained service technicians ...viiiInspecting for unsafe conditions ...

Table 4. Parts listing, Types 6399 (depending on your model)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRU partnumbe

Table 4. Parts listing, Types 6399 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 4. Parts listing, Types 6399 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 4. Parts listing, Types 6399 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 4. Parts listing, Types 6399 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 4. Parts listing, Types 6399 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 5. Parts listing, Types 6419 (depending on your model)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRU partnumbe

Table 5. Parts listing, Types 6419 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 5. Parts listing, Types 6419 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 5. Parts listing, Types 6419 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Installing a hot-swap power supply ...96Removing a memory module...97Installing a memory module ...98Remo

Table 5. Parts listing, Types 6419 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 5. Parts listing, Types 6419 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRU partnumbe

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

Table 6. Parts listing, Types 6429 (depending on your model) (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)F

7249810111252422236512141518191320161721326Table 7. Parts listing, Types 4203Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-serv

Performing the checkout procedure ...171Checkpoint codes (trained service technicians only) ...171Troubleshooting tables ...

Table 7. Parts listing, Types 4203 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart number6 Hard disk d

Table 7. Parts listing, Types 4203 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart number20 Microproce

Table 7. Parts listing, Types 4203 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart numberAdapter, NetX

Table 7. Parts listing, Types 4203 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart numberRSA Slimline

Table 8. Parts listing, Types 4206Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart number1 Power supply 670W (mode

Table 8. Parts listing, Types 4206 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart number7 Entry &

Table 8. Parts listing, Types 4206 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart number20 Microproce

Table 8. Parts listing, Types 4206 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart numberpower supply

Table 8. Parts listing, Types 4206 (continued)Index DescriptionCRU partnumber(Self-service)CRU partnumber(Optional-service)FRUpart numberQlogic ISCSI

Power cordsFor your safety, Lenovo provides a power cord with a grounded attachment plug touse with this Lenovo product. To avoid electrical shock, al

Taiwanese Class A warning statement ...228Chinese Class A warning statement ...228Korean Class A warning statement ...

Table 9. Power cords, Type 4203 (continued)Lenovo Power cordpart number Used in these countries and regions39M5144 Bangladesh, Lesotho, Macao, Maldive

Table 10. Power cords, Type 4206Lenovo Power cordpart number Used in these countries and regions39M5247 Taiwan (models 12V)39M5206 China (models)39M51

Table 10. Power cords, Type 4206 (continued)Lenovo Power cordpart number Used in these countries and regions39M5081 110 - 120 VAntigua and Barbuda, Ar

Table 11. Power cords, Type 6398Lenovo Power cordpart number Used in these countries and regions39M5247 Taiwan (models)39M5206 China (models)39M5102 A

Table 11. Power cords, Type 6398 (continued)Lenovo Power cordpart number Used in these countries and regions39M5081 110 - 120 VAntigua and Barbuda, Ar

Table 12. Power cords, Type 6399Lenovo Power cordpart number Used in these countries and regions39M5247 Taiwan (models)39M5206 China (models)39M5102 A

Table 12. Power cords, Type 6399 (continued)Lenovo Power cordpart number Used in these countries and regions39M5081 110 - 120 VAntigua and Barbuda, Ar

Table 13. Power cords, Type 6419Lenovo Power cordpart number Used in these countries and regions39M5247 Taiwan (models 11V 13V)39M5206 China (models)3

Table 13. Power cords, Type 6419 (continued)Lenovo Power cordpart number Used in these countries and regions39M5081 110 - 120 VAntigua and Barbuda, Ar

Table 14. Power cords, Type 6429Lenovo Power cordpart number Used in these countries and regions39M5247 Taiwan (models 12V 13V)39M5206 China (models)3

SafetyBefore installing this product, read the Safety Information.Antes de instalar este produto, leia as Informações de Segurança.Pred instalací toho

Table 14. Power cords, Type 6429 (continued)Lenovo Power cordpart number Used in these countries and regions39M5095 220 - 240 VAntigua and Barbuda, Ar

Chapter 4. Removing and replacing server componentsReplaceable components are of three types:v Self-service customer replaceable unit (CRU): Replaceme

v When you are finished working on the server, reinstall all safety shields, guards,labels, and ground wires.v For a list of options for the server, s

Handling static-sensitive devicesAttention: Static electricity can damage the server and other electronic devices.To avoid damage, keep static-sensiti

Removing and replacing Self-service CRUsReplacement of Self-service CRUs is your responsibility. If Lenovo installs aself-service CRU at your request,

Replacing the bezelTo replace the bezel, complete the following steps:1. Insert the tabs on the bezel into the slots on the server chassis.2. Rotate t

Removing the side coverAttention: Operating the server for more than 30 minutes with the side coverremoved might damage server components. For proper

Installing the side coverAttention: For proper cooling and airflow, replace the side cover before turning onthe server. Operating the server for exten

Turning the stabilizing feetTo rotate the front feet, complete the following steps.Feet1. Carefully position the server on a flat surface. The feet sh

Removing an adapterTo remove an adapter, complete the following steps.1. Read the safety information that begins on page vii and “Installation guideli